GreenIQ GIQ-USWIF-001/EN Guia de Instalação Página 1

!Smart Garden Hub"Installation GuideRevision 2.5, March 2015 www.greeniq.co

4. Follow the instructions on the screen. If the browser asks for permission to access your location, you should accept. Your location is be

2.3. Setting up Wi-Fi connection If you plan to use the unit with an Ethernet cable (Wired-Mode) you can skip this section. To use the un

Network indicator always turns on for the first few seconds. If it then turns off, it means that the unit could not connect to the Internet.

14. Disconnect the Ethernet Cable from the unit. 15. Connect to power again. 16. Go to the “Status” screen and wait a few minutes to make sure

1. The unit’s operating temperature range is -20°C to 55°C (-4°F to 131°F). Please avoid exposing the unit to direct sunlight or other heat

4. Connect the power jack to the unit’s Power Adapter Port, and place the Power Adapter wire as shown in Figure 2. Figure 2 14CorrectIncor

5. If you are using Ethernet Cable to connect to the Internet (Wired-Mode), you need to break the Ethernet Port sealing tab on th

6. Place the cover on the unit. Use the GreenIQ Screwdriver and the three cover screws from the mounting kit to tighten the cover

The following table shows the color code of Cable 1.""Warning: Never shortcut a GreenIQ wire with other GreenIQ wire. CABLE 1ColorCodeDetail

Tip: Before replacing your old irrigation controller, you can use the supplied sticker kit to mark the existing wires. Figure 4 shows an example

3.4. Connecting Sensors Your GreenIQ Smart Garden Hub supports 3 types of sensors: 1. Standard Rain Sensor. 2. Flow meter. 3. Up to 3 analog sensors.

The following table shows the color code of Cable 2.""Warning: Never shortcut a GreenIQ wire with other GreenIQ wire."CABLE 2ColorCodeD

The two wires of an optional standard rain sensor (not supplied) should be connected as follows: one to wire “R” and the other to wire “VC

Figure 5 shows an example of an electrical scheme. Figure 5 22Garden lighting should be wired only by an authorised electrician.

3.6. Completing the connectivity After completing the wiring, make sure that the unit is connected to power. If Wired-Mode is selected, you need to co

6. Select “Zone 1”, and turn on the “Zone Enable” and “Manual” switches. This should operate the sprinklers in Zone 1. Please note that the initial re

3.8.Technical Specifications Size and Weight • GreenIQ Smart Garden Hub: ◦ Diameter: 15.0 cm (5.91 inches) ◦ Depth: 5.3 cm (2.09 inches) ◦ Weight: 392

Input Ports • Flow meter • Rain sensor • 3 Analog sensor inputs (0VDC to 3.3VDC) Power Adapter • Output: 24VAC, 1A (included) Communication • Ethernet

GIQ-0020-02 © 2015 All Rights Reserved to GreenIQ LTDyour home just got smarter.

1. Your GreenIQ Smart Garden Hub 1.1. Welcome Thank you for purchasing the GreenIQ Smart Garden Hub. The GreenIQ Smart Garden Hub allows you

You have full control of your GreenIQ Smart Garden Hub via your iPhone, iPad, Android smartphone/tablet, PC, Mac and other web-enabled devices.

•Make sure not to swap Cable-1 and Cable-2. Swapping cables might cause permanent damage to your Smart Garden Hub. •Always use the provided

•User Guide •Wire Labels Kit •GreenIQ User Card •GreenIQ Screwdriver •Mounting Kit •Power Adapter •1-Meter Ethernet Cable 1.5. Technical Support It i

1.6. GreenIQ Smart Garden Hub diagram Figure 1 shows the GreenIQ Smart Garden Hub diagram. Figure 1 6123456789

1. Cover 2. Power Indicator 3. Network Indicator 4. Cover Screws (x3) 5. Mounting Holes (x2) 6. Cable 1 Port 7. Cable 2 Port 8. Ethernet Port (RJ-45)

2. Initial Configuration 2.1. General It is highly important to activate the unit before installing it at its designated location. 2.2. Activating your